RRP Proguard Bolt On front mudguard 2023

The RRP ProGuard Bolt On is the first large direct mount mudguard of its type, it offers outstanding protection with the slickest most factory look available. There are no zip ties or velcro straps to ruin the clean lines on your bike as they are secured by bolts (supplied). We also have TILT BRACKETS which allow you to fine tune the fit angle of the mudguard, you can tilt the front/back up or down a few millimetres with 2 brackets (supplied).

Features

• FIRST LARGE DIRECT MOUNT MUDGUARD OF ITS KIND
• NO ZIP TIES OR VELCRO STRAPS
• NEATEST LOOKING LARGE MUDGUARD ON THE MARKET
• EASILY REMOVED IN SECONDS
• HEIGHT ADJUSTABILITY BY 6MM
• ANGLE ADJUSTABILITY FOR BETTER FIT IF NEEDED VIA 2 TILT BRACKETS
• 2 THICK RUBBER PADS TO PROTECT YOUR FORKS
• MINI SIZE – GREAT ALL YEAR ROUND MUDGUARD OFFERING GOOD PROTECTION
• STANDARD SIZE – OFFERS VERY HIGH LEVELS OF PROTECTION
• STICKER RECESS FOR EASY FIT AND STICKER PROTECTION
• OUR SPECIAL PROVEN POLYPROPYLENE MIX IS USED FOR MAXIMUM DURABILITY AND FIT
• BEAUTIFUL STYLING – EASY CLEAN MATTE TEXTURED FINISH WITH GLOSS HIGHLIGHTS
• LONG FRONT TO COPE WITH HIGH SPEED MUD AND SPRAY
• SMALL TURN DOWN AT FRONT TO DEFLECT SPRAY AND FOR BETTER TYRE CLEARANCE
• LONG REAR WITH RAISED FLICK OFFERS MORE PROTECTION ESPECIALLY WHEN THE WHEEL IS TURNED
• PROVEN SEAL SHIELD TO INCREASE FORK PROTECTION AND EXTEND SERVICE INTERVALS
• WHEELS COMPATILITY : 26", 27.5", 29"
• TYRES COMPATIBILITY : UP TO 3"
• FORKS COMPATIBILITY:
    - FITS FOX 32, 34, 36, 38, 49 FORKS - STD & BOOST (doesn’t fit FOX 40 in 26” or 27.5” without our adapter bracket)
    - FITS NEW MARZOCCHI FORKS* (using the FOX chassis)
    - FITS OHLINS FORKS (use outer two bolts on RFX34)
    - FITS SR SUNTOUR FORKS (Some SR SUNTOUR forks have an unthreaded straight through hole in the centre of the fork brace, you can purchase a SLEEVE PACK to allow the PROGUARD BOLT ON to fit these forks (sold separately)

Included

• One Proguard Bolt On mudguard
• Rubber pads
• Two M3x2 bolts (Fox/Marzocchi)
• Two M4x3 bolts (Ohlins)
• Two M6x1 bolts (SR Suntour)
• Allen Key

Fitting

• The ProGuard - BOLT ON is our direct mount front mountainbike mudguard designed for big spray and mud protection (DISC BRAKE ONLY)
• IMPORTANT: You must apply the rubber adhesive side pads to the recess on the mudguard side wings, they protect your fork legs and provide vital stability and resonance damping
• Clean the fork threads and the fork legs MAKING SURE YOU DRY THE THREADS THOROUGHLY
• Select the correct bolts for your fork (details below) and run these into the threads WITHOUT the mudguard which will 'PRIME' and clean the threads before fitting, this part is important (YOU MAY NEED TO RE-TAP THE THREADS IF DEBRIS / PAINT IS LEFT IN THE THREADS FROM THE MANUFACTURE OF THE FORKS)
• Squeeze the side wings of the mudguard hard and slide under the fork brace from the rear with the wheel and tyre still in place
• You should be able to locate the mudguard and let go as the rubber side pads should hold it in place (ensure the slots are centrally aligned to the threaded holes on your fork)
• Use the Allen key provided to screw the bolts in EVENLY a bit each side, go gentle to start off to ensure you DON'T CROSS THREAD THEM, stop once it's pulled together so you can still move it
• Check alignment of the mudguard to ensure the distance from the tyre is even front and back, if you need to adjust the alignment then remove the mudguard and clip-on the appropriate TILT BRACKET found in the packaging (see example below). There are 2 TILT BRACKETS, one raises the front of the mudguard up and the other lowers it down (written on the TILT BRACKET)
• You can also change the height of the mudguard by 6mm through the slots for more clearance. NOTE: Highest position offers the most stability with the best mud clearance
• Finally tighten the bolts to the torque settings below: TORQUE SETTINGS: FOX, MARZOCCH & OHLINS = 1nm | SR SUNTOUR = 2nm
• NOTE: ONLY USE THE RRP SUPPLIED BOLTS AS THESE ARE SPECIFICALLY SELECTED OR DESIGNED FOR THE MUDGUARD - USING OTHER BOLTS MAY INVALIDATE WARRANTY - REPLACEMENT BOLTS PACKS ARE AVAILIBLE
• IMPORTANT - YOU MUST CHECK BOTTOM OUT CLEARANCE, LET MOST (BUT NOT ALL) OF THE AIR OUT OF YOUR FORK AND COMPRESS TO TEST IF THE CROWN OF THE FORK HITS THE MUDGUARD WHEN BOTTOMING. LOWER THE MUDGUARD THROUGH THE SLOTS IF YOU NEED MORE CLEARANCE, IF YOU CAN'T LOWER FURTHER THEN DO NOT USE

Important

• Bolts must be checked after each ride to ensure the mudguard is secure
• Remove mudguard every few rides to clean the brace / threads and fork legs
• DO NOT USE IN STICKY / CLAGGY MUD AS IT MAY BLOCK AND CAUSE INJURY OR DAMAGE
• MIN CLEARANCES - 18mm from the tyre when fitted and 10mm from the frame (on bottoming)
• INSPECT BEFORE YOU RIDE: DO NOT USE IF DAMAGED IN ANY WAY AS CONTINUED USE MAY LEAD TO FAILURE OR INJURY

Weight : Mini 104 gr , Standard 130 gr (without bolts)